DEVELOPING A LOGGING UNIT FOR MEASURING AND RECORDING POWER DATA USING ARDUINO BOARD

Document Type : Original Article

Authors

1 Researcher, Ag. Eng. Res. Inst., Ag. Res. Center, Dokki, Giza, Egypt.

2 Sen. Res., Ag. Eng. Res. Inst., Ag. Res. Center, Dokki, Giza, Egypt.

Abstract

A logging unit for measuring and recording power data for tillage implements was investigated. The system of sensor for a continuous and real time measurement of draft data is a set of electronic circuit made around the Arduino UNO board. It consisted of a conditioning circuit for strain gauges pull meter.  The developed system was an alternative of the commercial data logger namely Daytronic system 10K4 in draft measurement system(Khadr, 2008). As with the hardware, the Arduino integrated development environment is open source and can be down-loaded freely from the project’s internet website for programming, serves for compiling and up-loading programs to the microcontroller. Laboratory evaluation demonstrated that the developed system has been successfully gathered data from strain gauge pull meter.  The entire system was fixed on a tractor and a field experiment with chisel plow was conducted to evaluate the performance of the developed instrumentation system by determining the required chisel plow draft. The plowing speed measurement was done manually. The drawbar pull was measured at three tractor plowing speeds. The draft results were compared with those obtained through ASAE (2000) equation for chisel plow and the relative error was about 27%.  The very limited cost of the system presented in this paper could represent a step towards a more widespread application of accurate monitoring of tillage and tractor performance data potential, leading to an improvement of farm machinery management.

Keywords

Main Subjects

References

Aboukarima, A. M. (2007). Draft models of chisel plow based on simulation using artificial neural networks. Misr J. Agric. Eng., 24:42-61.
Al-Hamed, S.A. and A.A. Al-Janobi (2001). An Object-oriented program to predict tractor and machine system performance. Res. Bult., No. (106), Res. Cent. Coll. of Agri., King Saud Univ., pp. (5-24).
Al-Janobi, A. (2000). A data-acquisition system to monitor performance of fully mounted implements. Journal of Agricultural Engineering Research, 75(2): 167-175.
Almaliki, S., R. Alimardani and M. Omid (2016). Fuel consumption models of MF285 tractor under various field conditions.   CIGR Journal,18(3):147-158.
Al-Suhaibani, S. A. and A. E. Ghaly, 2010. Performance evaluation of a heavy duty chisel plow at various tillage depth and forward speeds. American J. of Engineering and Applied Sciences, 3 (4): 588-596.
Al-Suhaibani, S.A., A.A. AL-Janobi and Y.N. Almajhadi (2006).Tractors and tillage implements performance. CSBE/SCGAB 2006 Annual Conference Edmonton Alberta July 16 - 19, 2006, Paper No. 06-129
ASAE (2000). ASAE Standards D497.4 Agricultural Machinery Management Data, In: ASAE Standards 2000, (372-380) St. Joseph, MI.
Askari, M. and S. Khalifahamzehghasem (2013). Draft force inputs for primary and secondary tillage implements in a clay loam soil. World Applied Sciences Journal, 21 (12):1789-1794.
Bolton, W.  (1994). Engineering science, 2nd ed. Oxford: Newnes.
David, A. M., M. Banzi, D. Cuartielles and T. Lgoe (2007).  Arduino: an open electronics prototyping platform. Conference on human factors in computing systems San Jose, California, USA.
Dedrick,  R.R., J.D. Halfman and D.B. McKinney (2000). An inexpensive, microprocessor-based, data logging system. Comput. Geosci., 26:1059-1066.
Elashry, E. R., A.M. Bassuni, A. A. Sayed Ahmed and K.A. Ahmed (1994). An instrumentation system for measuring the tractor performance. Misr J. Agric.Eng.,11 (4):968-987.
El-Gwadi, A. A. (2005). Developing a locally manufactured slip ring torque transducer for PTO operating implements. Annual Conference of the Misr Society of Agr. Eng., 14-15 December 2005.
Ferdoush, S. and X. Li (2014). Wireless sensor network system design using raspberry Pi and Arduino for environmental monitoring applications. The 9th International Conference on Future Networks and Communications (FNC'2014)/The 11th International Conference on Mobile Systems and Pervasive Computing (MobiSPC'14), Ontario, Canada, August 17–20, vol. 34, pp. 103–110.
Fisher D.K. and H. Kebede (2010). A low-cost microcontroller-based system to monitor crop temperature and water status. Comput. Electr. Agric. 74:168-73.
Fisher D.K. and P.J. Gould (2012). Open-source hardware is a low-cost alternative for scientific instrumentation and research. Modern Instrument. 1:8-20.
Ghaly, A. and S. Al-Suhaibani, (2010). Effect of plowing depth of tillage and forward speed on the performance of a medium size chisel plow operating in a sandy soil. American Journal of Agricultural and Biological Sciences, 5:247-255.
Harrigan, T. M. and C.A. Rotz (1994). Draft of major tillage and seeding equipment. ASAE Paper No. 94-1533. ASAE, St. Joseph, MI 49085.
Hoffmann, K. (2001). Smart Materials. Berlin, Heidelberg: Springer Berlin Heidelberg.
Hut, R. (2013). New observational tools and data sources for hydrology: hydrological data unlocked by tinkering. Master Thesis, Delft University of Technology, Amsterdam, Netherlands. 
Iman, A. (2017). Evaluation of a chisel plow draft force and power estimation as based on the required mechanical laws. Iranian Journal of Biosystems Engineering (Iranian Journal of Agricultural Sciences), 47 (4): 625- 632 (Abstract in English).
Jithender, B., D.V. Sunitha, K. Upender and K.V.S. R. Reddy (2017). Performance study of tractor operated rotary plough in two different soils. Int. J. Curr. Microbiol. App.Sci., 6(10): 871-878.
Kadimi, J. and R. J. Dheeraj (2014). The TRACALTOR: automated farm area calculator and direction monitoring. International Journal of Computer Applications, 106(5):29 -32.
Kashyap, N. (2015). Design of low cost multi channel data acquisition system for meteorological application. Unpublished MSc Thesis, Department of Electronics and Communication Engineering National Institute of Technology, Rourkela, Odisha.
Khadr, Kh.A.A. (2004). Energy requirements for some seed-bed preparation implement under Egyptian conditions. The 12th annual conference of the Misr Society of Agricultural Engineering, PP: 481-491.
Khadr, Kh.A.A. (2008). Effect of some primary tillage implement on soil pulverization and specific energy. Misr J. Ag. Eng., 25(3): 731-745.
Mayer, F. T. (2016). Development of a measuring system to detect oads acting between the binding and the roller ski. Master Thesis in Mechanical Engineering, Norwegian University of Science and Technology, Faculty of Engineering Science and Technology, Department Engineering Design and Materials.
Nada, A.A. (2003). Developing an electric continuous mass fuel measuring system. The 11th Annual conference of Miser society of Agr. Eng. Oct. 2003: 273-282.
Nassir, A.J., M. N. Ramadhan and S.D. Mohssein (2016). Studying draft requirements and plowing specifications for chisel plow in silty clay soil. AL-Muthanna Journal of Agricultural Sciences, 4(1):100-119 (In Arabic).
Ndisya, J., A. Gitau, D. Mbuge  and A. Hiuhu (2016). The effect of the operational parameters on the draft requirement of ripping in a sandy clay soil. Open Journal of Optimization, 5: 1-13. 
Ranjbarian, S., M. Askari and J. Jannatkhah (2017). Performance of tractor and tillage implements in clay soil. Journal of the Saudi Society of Agricultural Sciences, 16(2):154-162.
Rasool, S., H. Raheman and G. Upadhyay (2017). Development of an instrumentation system for evaluating the tractive performance of walking tractors. International Journal of Current Microbiology and Applied Sciences, 6(10):759-770.
RNAM, (1995). RNAM test codes and procedures for farm machinery/Economic and Social Commission for Asia and the Pacific, Regional Network for Agricultural Machinery. RNAM technical publications: 12. Bangkok, Thailand.
Sahu, R.K. and H.A. Raheman (2006). Draught prediction of agricultural implements using reference tillage tools in sandy clay loam soil. Biosystems Engineering, 94:275-284.
Singh, C. D. and R. C. Singh (2011). Computerized instrumentation system for monitoring the tractor performance in the field. Journal of Terramechanics, 48(5): 333-338.
Ştefănescu, D. (2011). Handbook of Force Transducers: Principles and components. Berlin: Springer Verlag.
Tatović, M., A. Milovanović and I. Karapandžić (2016). Device for the remote measurement of meteorological data based on Arduino platform.  Serbian Journal of Electrical Engineering,13(1):133-144.
Teli, S. and  C. Mani (2015). Smart real time embedded Arduino based data acquisition system. International Journal of Research in Engineering and Technology, 4(8):258-262.
Thalheimer, M. (2013). A low-cost electronic tensiometer system for continuous monitoring of soil water potential. Journal of Agricultural Engineering, 44(3), p. e16.
Younis, S. M., E. R. Elashry, A. F. Bahnasy and I. M. Elsybaee (2010). Development a local system for measuring tractors performance. Misr J. Ag. Eng., 27(1):34 – 53.
Zadeh, S.R. A. and R. L. Kushwaha (2006). Development of a tillage energy model using a simple tool. CSBE/SCGAB Annual Conference, Edmonton Alberta, July 16 - 19, 2006: 1- 14.

Files

Share

How to cite

Statistics