MANUFACTURING AND PERFORMANCE EVALUATION OF A PROTOTYPE WOOD CHIPPING MACHINE TO PRODUCE MINI-CHIPS

Document Type : Original Article

Authors

1 Assist. Prof., Agric. Eng. Dept., Fac. of Agric., Zagazig Univ., Egypt.

2 Lecturer, Agric. Eng. Dept., Fac. of Agric., Tanta Univ., Egypt.

Abstract

The oversize wood chips are existing in the conventional disc chipper production even with tuning the chipper settings which is not convenient to be used in the some applications that need to small sizes chips as biomass pellets or poultry litter for instances, hence there is an urgent need to produce mini-chips (MCHIPS) to become abundant for wide range of agricultural utilization within the farm. Thus, the present study aims to manufacture and evaluate the performance a local made prototype wood chipping machine by providing the conventional wood disc chipper with built-in swinging hammer mill and concave screen behind the cutting disc on the same rotating shaft using the pruning residues of mango trees to produce MCHIPS with high quality (uniform chips with minimum fines) and low energy requirement. The performance of the chipping machine was evaluated under operational variables including; three cutting rotational speeds of 750, 1000 and 1250 rpm corresponding to peripheral speeds of 17.66, 23.55 and 29.43 m/s, respectively, three cutting angles of 48°, 50°, 54° and 58°, three concave screen sizes of 12, 16 and 20 mm, where the hammers has the same rotational speed of the cutting disc. The machine performance was investigated taking into consideration the machine productivity, particle size distribution, and energy requirement. The results indicated that, it is recommended to use the prototype chipping machine at cutting speed of 1000 rpm (23.55 m/s), cutting angle of 58° and screen size of 16 m to obtain the best MCHIPS particle size distribution (MCHIPS ≤3 mm= 6.05 %, MCHIPS >3-8 mm= 24.07 %, MCHIPS >8-12mm = 39.95% and MCHIPS >12-16mm=29.93 %) to achieve regular MCHIPS with minimum fines at machine productivity of 1.40 Mg/h and consumed energy of 12.35 kW.h/Mg.

Keywords

Main Subjects

References

Abdallah, R., S. Auchet and P.J. Méausoone (2011). Experimental study about the effects of disc chipper settings on the distribution of wood chip size. Biomass and Bioenergy, 35(2): 843-852.
Alakangas, E., J. Valtanen and J. E. Levlin (2006). CEN technical specification for solid biofuels—Fuel specification and classes. Biomass and Bioenergy, 30(11): 908-914.
Assirelli, A., V. Civitarese, R. Fanigliulo, L. Pari, , D. Pochi, E. Santangelo and R. Spinelli (2013). Effect of piece size and tree part on chipper performance. Biomass and Bioenergy, 54: 77-82.
 Atiya, E. A., M.M. Morad, M.A. Tawfik and K.I. Wasfy (2017). Fabricating and performance evaluating of an experimental prototype of downdraft biomass gasifier. Zagazig J. Agric. Eng., 44 (2):727-740.
 Bakr, M.M.A., M.A. El-Shazly, M.A. Tawfik and Y.S. Abdellah (2016).Study on some factors affecting the manufacturing of cattle feed pellets. Zagazig J. Agric. Eng., 43 (6A):2177-3195.
Di Fulvio, F., G. Eriksson, and D. Bergström (2015). Effects of wood properties and chipping length on the operational efficiency of a 30 kW electric disc chipper. Croatian Journal of Forest Engineering, 36(1): 85-100.
Facello, A., E. Cavallo, N. Magagnotti, G. Paletto and R. Spinelli, (2013). The effect of chipper cut length on wood fuel processing performance. Fuel Proces. Technol., 116:228-233.
FAO (2017). BEFS Assessment for Egypt: Sustainable bioenergy options from crop and livestock residues, Rome – Italy. Working paper: ISBN 978-92-5-109587-4.
Gendek, A. and A. Nawrocka (2014). Effect of chipper knives sharpening on the forest chips quality. Annals of Warsaw University of Life Sciences-SGGW. Agriculture, (64 Agric. Forest Eng.).
Gonçalves, R. and A. C. Néri (2005).Orthogonal cutting forces in juvenile and mature pinus taeda wood. Sci. Agric. (Piracicaba, Braz.), 62(4):310-318.
Hartmann, H., T. Bohm, P.D. Jensen, M. Temmerman, F. Rabier and M. Gloser (2006) Methods for size classification of wood chips. Biomass and Bioenergy, 30:944-953.
Hellström, L.M., P. Isaksson, P.A. Gradin and K. Eriksson (2009). An analytical and numerical study of some aspects of the wood chipping process. Nordic Pulp and Paper Res. J., 24(2): 225-230.
Ibrahim, M. K. (1982). Wet milling of wheat grain. M. Sc. Thesis, Faculty of Agric., Mansoura Univ., Egypt.
Jensen, P., J. Mattson, P. Kofman and A. Klausner (2004). Tendency of wood fuels from whole trees, logging residues and roundwood to bridge over openings. Biomass and Bioenergy, 26(2): 107–113.
Krajnc, M. and B. Dolšak (2014). The influence of drum chipper configuration on the quality of wood chips. Biomass and Bioenergy, 64: 133-139.
Nati C., R. Spinelli and P.G. Fabbri (2010).Wood chips size distribution in relation to blade wear and screen use. Biomass and Bioenergy, 34:583–587
Reczulski, M. ( 2013). Effect of disc chipper design parameters and physical properties of wood on chips thickness. Polish Paper Review 69(7): 344-350.
Reczulski, M. (2015).Aanalysis of the construction and operation of system wood chipping and transfer chips. Wood Res., 60(40): 671-678.
Reczulski, M. (2016). The system wood chipping in disc chipper-problems of uniformity of chips length. Wood Res., 61(3):433-442.
Spinelli, R. and B. Hartsough (2001). A survey of Italian chipping operations. Biomass and Bioenergy, 21:433–444.
Spinelli, R., B. Hartsough and N. Magagnotti (2005).Testing mobile chippers for chip size distribution. International Journal of Forest Engineering, 16: 29–36.
Spinelli, R., E. Cavallo, L. Eliasson, A. Facello (2013). Comparing the efficiency of drum and disc chippers, Silva Fennica, 47 (2): 11p https://doi.org/10.14214/sf.930.

Files

Share

How to cite

Statistics